Rotex Solenoid Valves

Specifications:

• MOC: CS, A 216 Gr. WCB
• Sizes: 15 to 200 NB
• Ends: Scr. BSPT/NPT/FLGD Table (F,H,J,K)/Flgd. # 150, 300
• PMA: 31.5 Kg/cm² (g)
• TMA: 427º C

Additional Information:

• Item Code: SEP-CS

Specifications:

• MOC: Cast iron
• Sizes: 15 to 25 NB (Single Window), 40 to 50 NB (Double Window)
• Ends: Scr. BSPT/BPT
• PMA: 13.0 Kg/cm²(g)
• TMA: 220º C

Specifications:

• MOC: CS, A216 Gr. WCB
• Sizes: 15 to 80 NB
• Ends: Scr. BSPT/NPT/SW/Flanged Ends
• PMA: 20.0 Kg/cm²(g)
• TMA: 250º C

Additional Information:

• Item Code: SG-20

SPECIFICATIONS :

 

 

 

 

Enclosure:

1. General Purpose Flying lead / Plug-in
2. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
3. Explosion-Proof with Junction box as per IS 2148 group I, IIA, IIB and IIC
4. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL (in
process) available.

MEDIA : 

Air, Inert Gases, Water, Vacuum, Free Flowing Liquid, 
Oil, Diesel,Kerosene, LPG, Furnace Oil. 

APPLICATION : 

Drain , Dispensing , Analyzer.

Rotex2 Port Isolated Piston External Air Operated Bi-Directional

SPECIFICATIONS :

 

 

Enclosure:

1. General Purpose Flying lead / Plug-in
2. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
3. Explosion-Proof with Junction box as per IS 2148 group I, IIA, IIB and IIC
4. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL 
(in process) available .

Media : 

Air, Inert Gases, Water, Vacuum, Free Flowing Liquid, 
Oil, Diesel, Kerosene, LPG, Furnace Oil

Applications : 

Ideally suited for application where flow is expected to pass through 
valve in bi-direction. Vacuum breaking.

* External pilot pressure should be minimum 2 bar or >= main fluid pressure whichever is higher.

SPECIFICATIONS:

 

 

 

Media : 

Air, Inert Gases, Water, Free Flowing Liquid,Oil, Diesel, Kerosene

Applications : 

Can be used as 2/2 NC by using 3/2 NO Pilot

 

NOTE : 

The External Air Pressure should be minimum 2 bar or >= main fluid pressure whichever is higher.

USE 3/2 NO PILOT TO USE THIS VALVE AS NC.

SPECIFICATIONS :

 

 

 

 

Media : 

Air, Inert Gases, Water, Vacuum, Free Flowing Liquid, 
Oil, Diesel, Kerosene, LPG, Furnace Oil

Applications : 

Ideally suited for ON/ OFF control of fuel gas 

* The External Air Pressure should be minimum 2 bar or >_ main fluid pressure whichever is higher.

Rotex offers a wide range of 3 Port Solenoid Valves to suit variety of applications. These valves can be basically classified as Normally Closed ,Normally Open or Universal (for mixing or diverting function) based on the valve condition when the solenoid is energized.

Further they can be classified as Direct Acting, Internal / External Pilot Operated.

Rotex 3 Port Valves can operate upto a pressure range of 150 bar. Basically the valves can be operated between (-)20 °C to 80 °C temperature. These valves are generally found in the of 0.5mm to 80mm orifice thus offering a wide range of flow rates.

These valves can be mounted in any position. There are non sliding parts and they are positively sealed against pressure. These valves can be operated for above 10 million cycles.

Rotex valves are made of mainly Anodized Aluminum, Brass, SS316. The seals are mostly made of NBR, Viton, EPDM, PTFE.

Rotex 3 Port Valve provides interchangeability for various solenoid enclosures, voltage and current without affecting its performance.

Request
Callback

Rotex Manufacturing 2 Port, 3 Port and 5 Port subbase Mounted Solenoid Valve with Various Types of solenoid enclosures, Voltagw and current.Subbase Solenoid Valve is available with different types of Manifold. This valve is also available with High prerssure.Rotex Supplies 3 Types of manifold for 2,3,4, and 5 port solenoid valves. Manifold single sided, Manifold double sided and manifold with Isolation Cock.

5 PORT, 3 PORT CONVERTIBLE, INLINE POPPET, NAMUR SOLENOID VALVE

• Voltage, Current and enclosure can be changed by replacing solenoid without affecting performance of the valve
• Easily Serviceable
• Body material Aluminium and Ss 316
• Life 60 million cycles
• Fast acting up to 1000 cycles per minute
• Exhaust ports can be blocked for speed regulation
• Can be supplied with NAMUR 2,3 and 4
• Larger Exhaust for faster operation of the actuator
• slim poppet design
• In 3/2 mode exhaust purged into the spring chamber of pneumatic actuator
• Manual override provided
• Suitable for Air, Gas, Water, Oil
• O ring and Fasteners to mount solenoid Valve on the actuator are provided
• Temperature - 20 °C to 70 °C
• Lubrication not necessary
• 5/2, 3/2 convertible at site without need of any special tools

3 PORT POPPET DESIGN NAMUR SOLENOID VALVE

• Poppet design
• Manual override provided
• Voltage, current and enclosure can be changed by replacing solenoid without affecting performance of the valve
• Sutable for Air ,Gas, water, Oil
• O Rings and fasteners to mount solenoid valve on the actuator are provided
• Temperature -20 °C to 70 °C
• Exhaust purged into the spring chamber of pneumatic actuator
• Lubrication not necessary
• Direct acting large Orifice

Product Details:

Rotex offers a wide range of 5 Port Solenoid Valves to suit variety of applications. These valves are Universal (for mixing or diverting function) based on the valve condition when the solenoid is energized.

Further they can be classified as Internal / External Pilot Operated, Air Operated.

Rotex 5 Port Valves can operate up to a pressure range of 70 bar. Basically the valves can be operated between (-) 20 °C to + 80 °C temperature. These valves are generally found in the of 6 mm to 50 mm orifice thus offering a wide range of flow rates.

These valves can be mounted in any position. There are non sliding parts and they are positively sealed against pressure. These valves can be operated for above 10 million cycles.

Rotex valves are made of mainly Anodized Aluminium, Brass, SS 316. The seals are mostly made of NBR, Viton, EPDM, PTFE.

Rotex 5 Port Valve provides interchangeability for various solenoid enclosures, voltage and current without affecting its performance

GENERAL FEATURES OF PULSE JET VALVES :

• Pulse valves are manufactured from 1/2" to 3"
• Life is greater than 10 million cycles
• Remote pilot version is also available
• Springless design ensures longer life
• Special design made having studied Tank geometry
• Material of construction is stainless steel and aluminium
• Double diaphragm for 40mm and above
• Higher flow factor ensures better cleaning
• Can be mounted in any position
• Quick On / Off time.
• Profiled seat avoid particle trapping
• Peak Pressure ratio greater that 80%
• Explosion proof version also available
• Less power consumption
• Hytrel Diaphragm for longer life
• Vent protected by silencer
• Low Decibel noise level

 

DESIGN FEATURES :

• Dual Diaphragm for longer life
• Pilot vent protected by silencer
• Life > 10 million cycle
• High Flow factor for effective cleaning
• Lower air consumption / Pulse
• Pressure Die cast epoxy coated aluminum/ Stainless Steel cast Body
• Unique profile of the Diaphargm eleminates spring
• profiled seat to avoid dust/particle trapping while closing
• Stainless steel Fasterners
• Valve can be mounted in any position
• For Corrosion resistance Stainless Steel cast weather / Explosuon proof Solenoid

Rotex 3 Port 2 Position Direct Acting Normally Closed Solenoid Valves

Specifications :

 

 

 

 

Enclosure:

1. General Purpose Flying lead / Plug-in
2. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947

Media : 

Air, Inert Gases

Applications : 

Single acting actuator / Cylinder, control valve actuation.

Specifications ::

 

 

 

 

Enclosure:

1. General Purpose Flying lead / Plug-in
2. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
3. Explosion-Proof with Junction box as per IS 2148 group I, IIA, IIB and IIC
4. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL 
(in process) available.

Media : 

Air, Inert Gases, Water, Vacuum Free Flowing Liquids, 
Oil, Diesel, Kerosene, LPG.

Applications : 

Single acting actuator/ Cylinder, control valve actuation. 
Diverting / mixing of fluid, analyzer ESD.

* For Valve type 30334 operated with AC voltage select solenoid with inbuilt full rectifier `FR` option.

Specifications :

 

 

 

 

Enclosure :

1. General Purpose Flying lead / Plug-in
2. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
3. Explosion-Proof with Junction box as per IS 2148 group I, IIA, IIB and IIC
4. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL 
(in process) available.

Media :

Air, Inert Gases.

Applications :

Single acting actuator / Cylinder, control valve actuation, ESD.

* The pressure drop at inlet port causes malfunction of the Valve. All equipment connected between the header and the inlet port should have a higher orifice compared to the solenoid Valve.

Request
Callback

Rotex 3 Port 2 Position Internal Pilot Operated Universal Valves

Specifications:

 

 

 

 

Enclosure:

1. General Purpose Flying lead / Plug-in
2. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
3. Explosion-Proof with Junction box as per IS 2148 group I, IIA, IIB and IIC
4. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL (in
process) available.

Media :

Air, Inert Gases, Water, Free Flowing Liquids.

Applications :

Single acting actuator / Cylinder, Control Valve actuation, ESD.

* The pressure drop at inlet port causes malfunction of the Valve. All equipment connected between the header and the inlet port should have a higher orifice compared to the solenoid Valve.

Request
Callback

Rotex 3 Port 2 Position External Pilot Operated Universal Valves

Specifications

 

 

 

 

Enclosure: 

1. General Purpose Flying lead / Plug-in
2. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
3. Explosion-Proof with Junction box as per IS 2148 group I, IIA, IIB and IIC
4. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL 
(in process) available.

Media :

Air, Inert Gases, Water, Vacuum, Free Flowing Liquid, 
Oil, Diesel, Kerosene, LPG.

Applications :

Single acting actuator / Cylinder, control valve actuation, 
Diverting / mixing of fluid, Analyzer.

* When valve is used for NC/ NO application, the Pilot pressure should be minimum 2 bar or >= main fluid pressure whichever is higher. When valve is used for diverting mixing application, the pilot pressure should be at least 2 bar higher than main fluid pressure.

Request
Callback

Specifications

 

 

 

 

Media :

Air, Inert Gases, Water, Vacuum, Free Flowing Liquid, 
Oil, Diesel, Kerosene, LPG, Furnace Oil .

Applications :

Quick operation of cylinder Actuator 

* When valve is used for NC/ NO application, the Pilot pressure should be minimum 2 bar or >= main fluid pressure whichever is higher. When valve is used for diverting mixing application, the pilot pressure should be at least 2 bar higher than main fluid pressure.

Request
Callback

Specifications:

 

 

 

 

Enclosure:

1. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
2. Explosion-Proof with Junction box as per IS 2148 group I, IIA, IIB and IIC
3. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL 
(in process) available.

Media :

Air, Inert Gases.

Applications :

Single acting actuator/ Cylinder, control valve actuation. Shut off valve.

* Valve type 32101 and 33301 When used for NC/ NO application, the Pilot pressure should be minimum 2 bar or >= main fluid pressure whichever is higher.

3 Port 2 Position Direct Acting Normally Closed/Open High Pressure (150 Bar) Solenoid Valve 

Specifications :

 

 

 

 

Enclosure:

1. General Purpose Flying lead.
2. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
3. Explosion-Proof with Junction box as per IS 2148 group I, IIA, IIB and IIC
4. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL 
(in process) available.

Media :

Air, Inert Gases, Water, Vacuum Free Flowing Liquids, 
Oil, Diesel, Kerosene, LPG, CNG.

Applications :

High Pressure Application.

3 Port 2 Positon Internal Pilot Operated Normally Closed/Open High Pressure Solenoid Valve

Specifications:

 

 

 

 

Enclosure: 

1. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
2. Explosion-Proof with Junction box as per IS 2148 group I, IIA, IIB and IIC
3. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL 
(in process) available.

Media :

Air, Inert Gases, Water.

Applications :

Single acting actuator/ Cylinder, control valve actuation.

Specifications:

• MOC: Cast Iron
• Sizes: 25 to 80 NB
• Ends: Ref. Product Cat. For Details
• PMA: 10.0 Kg/cm²(g)
• TMA: Ref. Product Cat. For Details

Additional Information:

• Item Code: SRJ-RRJ-RJ

Specifications:

• MOC: Brass/SS
• Sizes: 15 NB
• Ends: Scr BSP/NPT
• PMA: PN 16/PN 25
• TMA: 260º/400º C

Additional Information:

• Item Code: VB-14-VB-21

Specifications:

• MOC: Ref. Product Cat. For Details
• Sizes: 40, 50, 80 NB
• Ends: Ref. Product Cat. For Details
• PMA: 8.7 Kg/cm²
• TMA: 220° C

Additional Information:

• Item Code: PPPPU

Specifications:

• MOC: CI, IS 210 Gr. FG 260
• Sizes: 15 to 25 NB
• Ends: Scr. BSPT/NPT
• PMA: 10.0 Kg/cm²(g)
• TMA: 220º C

Additional Information:

• Item Code: SG-13